ELECTRIC TRIM TAB KITS 14 lencomarine.com Heavy Duty (HD) Performance Trim Tab Kits 12V System The Heavy Duty series is designed & built for the boats that need extra strength to support them in rougher water at higher speeds. Boat lengths 18' (5.5 m) to 42' (12.8 m) Blades are constructed of Electro-Polished 12-gauge (2.7 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 1/4" (6.4 mm) diameter hinge pin. Kits include: • (2) 12-gauge stainless steel Electro-Polished blades • (2) 15054-001 actuators with 6' (1.8 m) leads & Deutsch connectors • (2) 30133-103 actuator extension wiring harnesses - 20' (6.1 m) length • (2) 15085-001 upper mounting brackets with gland seal • (2) 50014-001 lower mounting brackets • Lenco owner's/installation manual • Stainless steel mounting hardware Blades are constructed of Electro-Polished 12-gauge (2.7 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 1/4" (6.4 mm) diameter hinge pin. Full transom back plate with welded on stainless steel upper & adjustable lower actuator mounting brackets, 5/16" (.8 cm) stainless steel mounting bolts & mechanical strain-relief cable seals. 3.75" (9.5 cm) sacrificial anodes installed. Kits include: • (2) 12-gauge stainless steel Electro-Polished blades • (2) 15055-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • (2) 30133-103 actuator extension wiring harnesses - 20' (6.1 m) length • Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer Standard Performance Trim Tab Kits 12V System Our first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13' (4 m) to 40' (12.2 m) 15037-101 Electro-Polished 15043-101 Electro-Polished Part # L" X W" Boat Length Hinge Height Min. Transom Height 15034-101 9" x 9" 13'–20' 2" (5.1 cm) 13.5" (34.3 cm) 15035-101 9" x 12" 16'–26' 2" (5.1 cm) 13.5" (34.3 cm) 15036-101 12" x 9" 16'–26' 2" (5.1 cm) 11" (27.9 cm) 15037-101 12" x 12" 18'–32' 2" (5.1 cm) 11" (27.9 cm) 15038-101 14" x 12" 19'–34' 2" (5.1 cm) 11" (27.9 cm) 15039-101 16" x 12" 20'–36' 2" (5.1 cm) 11" (27.9 cm) 15040-101 18" x 14" 22'–40' 2" (5.1 cm) 11" (27.9 cm) Part # L" X W" Boat Length Min. Transom Height 15041-101 12" x 12" 18'–34' 10.5" (26.7 cm) 15042-101 14" x 12" 19'–36' 10.5" (26.7 cm) 15043-101 16" x 12" 20'–38' 10.5" (26.7 cm) 15044-101 18" x 14" 22'–42' 10.5" (26.7 cm) = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Back Plate Dimensions 10" (25.4 cm) 12"(30.5 cm) 8" (20.3 cm) 5"(12.7 cm) 2" (5.1 cm) 15041-101 15042-101 15043-101 14"(35.6 cm) 6"(15.2 cm) 10" (25.4 cm) 8" (20.3 cm) 2" (5.1 cm) 15044-101 The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates. SHIPPED FULLY ASSEMBLED = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Switch kits sold separately See pages 30–32 Switch kits sold separately See pages 30–32
RkJQdWJsaXNoZXIy MjgzMDI=