ELECTRIC TRIM TAB KITS 15 lencomarine.com Part # L" X W" Boat Length Min. Transom Height 15045-101 17" x 12" 20'–40' 10.5" (26.7 cm) Part # L" X W" Boat Length Min. Transom Height 15046-101 19" x 14" 23'–45' 10.5" (26.7 cm) 15047-101 24" x 14" 25'–50' 10.5" (26.7 cm) 14"(35.6 cm) 6"(15.2 cm) 10" (25.4 cm) 8" (20.3 cm) 2" (5.1 cm) Extreme Duty (XD) Performance Trim Tab Kit 12V System / Single Actuator The only single actuator Extreme Duty design offered. This kit is similar to our Heavy Duty Performance series with a thicker, stronger blade for those boaters who run hard in extreme conditions. Boat lengths 20' (6.1 m) to 40' (12.2 m) Extreme Duty (XD) Performance Trim Tab Kit 12V System / Dual Actuator All the robust features of our single actuator XD series with twice the actuator power for larger, faster boats that don't back away from rough conditions. Boat lengths 23' (7 m) to 50' (15.2 m) Blades are constructed of Electro-Polished 10-gauge (3.4 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with mechanical strain-relief cable seals, welded on stainless steel upper & adjustable lower actuator mounting brackets, 3/8" (9.5 mm) stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed. Blades are constructed of Electro-Polished 10-gauge (3.4 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with mechanical strain-relief cable seals, welded on stainless steel upper & adjustable lower actuator mounting brackets, 3/8" (9.5 mm) stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed. Kit includes: • (2) 10-gauge stainless steel Electro-Polished blades • (2) 15056-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer • Note: Actuator extension harnesses not in kits, must be purchased separately (2 required) See page 42 Kits include: • (2) 10-gauge stainless steel Electro-Polished blades • (4) 15056-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer • Note: Actuator extension harnesses not in kits, must be purchased separately (4 required) See page 42 15045-101 Electro-Polished 15046-101 Electro-Polished Back Plate Dimensions 10" (25.4 cm) 12"(30.5 cm) 8" (20.3 cm) 5"(12.7 cm) 2" (5.1 cm) Back Plate Dimensions The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates. The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates. SHIPPED FULLY ASSEMBLED SHIPPED FULLY ASSEMBLED = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Switch kits sold separately See pages 30–32 Switch kits sold separately See pages 30–32
RkJQdWJsaXNoZXIy MjgzMDI=