ELECTRIC TRIM TAB KITS 18 lencomarine.com = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Part # Voltage L" X W" Boat Length 15018-101 12V 12" x 18" 24' – 40' 15019-101 12V 12" x 24" 27' – 44' 15020-101 12V 12" x 30" 30' – 48' 15021-101 12V 12" x 36" 33' – 52' Part # Voltage L" X W" Boat Length 15022-101 12V 16" x 24" 35' – 50' 15023-101 12V 16" x 30" 40' – 60' 15024-101 12V 16" x 36" 45' – 70' 15025-101 12V 16" x 42" 50' – 80' = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Super Strong Trim Tab Kits 12V & 24V Systems/ Single Actuator This Super Strong design is for sport fishing, large cruising and commercial vessels. This series has a completely flat blade design which reduces spray giving you a clean, dry ride. Boat lengths 24' (7.3 m) to 52' (15.8 m) Super Strong Trim Tab Kits 12V & 24V Systems/ Dual Actuator Offering the same features as our single system, this series gives you a longer blade design with dual actuator support for those large vessels needing that extra lift. Boat lengths 35' (10.6 m) to 80' (24.4 m) Blades are constructed of 7-gauge (4.6 mm) laser cut 304 stainless steel with 3/8" (9.5 mm) diameter hinge pin. High impact corrosion proof upper and lower mounting brackets with mechanical gland cable seal, 5/16" (.8 cm) upper and 3/8" (9.5 mm) lower stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed. Blades are constructed of 7-gauge (4.6 mm) laser cut 304 stainless steel with 3/8" (9.5 mm) diameter hinge pin. High impact corrosion proof upper and lower mounting brackets with mechanical gland cable seal, 5/16" (.8 cm) upper and 3/8" (9.5 mm) lower stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed. Kits include: • (2) 7-gauge stainless steel standard finish blades • (2) 15055-001 12 Volt (15062-001 for 24 Volt) XD Extreme Duty actuators with 6' (1.8 m) & Deutsch connectors • (2) 15140-001 120 Lower Mounting Brackets • Lenco owner's/installation manual • Stainless steel mounting hardware • Note: Actuator extension harnesses not in kits, must be purchased separately (2 required) See page 42 Kits include: • (2) 7-gauge stainless steel standard finish blades • (4) 15055-001 12 Volt (15062-001 for 24 Volt) XD Extreme Duty actuators with 6' (1.8 m) & Deutsch connectors • (4) 15140-001 120 Lower Mounting Brackets • Lenco owner's/installation manual • Stainless steel mounting hardware • Note: Actuator extension harnesses not in kits, must be purchased separately (4 required) See page 42 15018-101 15022-101 Switch kits & Harnesses sold separately Switches on pages 30–32 Harnesses on page 42 Switch kits & Harnesses sold separately Switches on pages 30–32 Harnesses on page 42 Part # Voltage L" X W" Boat Length 15026-101 24V 12" x 18" 24' – 40' 15027-101 24V 12" x 24" 27' – 44' 15028-101 24V 12" x 30" 30' – 48' 15029-101 24V 12" x 36" 33' – 52' Part # Voltage L" X W" Boat Length 15030-101 24V 16" x 24" 35' – 50' 15031-101 24V 16" x 30" 40' – 60' 15032-101 24V 16" x 36" 45' – 70' 15033-101 24V 16" x 42" 50' – 80'
RkJQdWJsaXNoZXIy MjgzMDI=