ELECTRIC TRIM TAB KITS 19 lencomarine.com Part # L" X W" Boat Length Min Transom Height 15162-103 21" x 14" 24' – 42' 10.5" (26.7 cm) 15163-103 25" x 14" 28' – 46' 10.5" (26.7 cm) Heavy Duty Trim Tab Kit 12V System The largest and strongest HD Trim Tab Series. Similar to our 10-gauge HD systems, this series was engineered using 7-gauge 1/4" thick stainless steel blades. While using a single actuator application, these systems perform best on larger vessels, including commercial applications, and go fast boats. Boat Lengths 24' (7.3 m) to 46' (14m) Blades are constructed of Electro-Polished 7-gauge (4.6 mm) laser cut 304 stainless steel, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with remote gland-seal, welded on stainless steel upper and a single adjustable lower C-channel bracket. 3/8" (9.5 mm) stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed. Kits include: • (1) Key Pad Assembly Indicator 30343-001 • (1) Switch Control Box Indicator 30368-001 • (2) 7-gauge stainless steel Electro-Polished blades • (2) Heavy Duty Actuators 15158-001 • (1) Lenco owner’s/installation manual • Note: Boat-mounting hardware to be supplied by customer • Note: Actuator extension harnesses not in kits, must be purchased separately (2) required See page 42 Two Piece indicator switch included with kit 15162-103 Electro-Polished SHIPPED FULLY ASSEMBLED 14"(35.6 cm) 6"(15.2 cm) 10" (25.4 cm) 8" (20.3 cm) 2" (5.1 cm) Back Plate Dimensions = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Heavy Duty Trim Tab Kit 12V System This Heavy Duty system is similar to our 7-gauge system, but with a wider trailing edge profile giving it a larger surface area when making trim adjustments. The sides and back edges of this blade are bent up at 90 degrees providing added strength to the blade. This HD system is engineered for boats that need strength along with extra lift from the wider trailing edge profile. Boat lengths 23’ (7.01m) to 50’ (15.24m) Blades are constructed of Electro-Polished 10-gauge (3.4 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with remote gland-seal, welded on stainless steel adjustable C-channel with 3/8" (9.5 mm) stainless steel mounting hardware and a 3.75" (9.5 cm) sacrificial anodes installed Kits include: • (1) Key Pad Assembly Indicator 3034-001 • (1) Control Box Assembly Indicator 30368-001 • (2) 10-gauge stainless steel electro-polished blades • (2) 15158-001 Heavy Duty actuators with 6’ (1.8 m) leads & Deutsch connectors • (1) Lenco owner’s/installation manual • Note: Boat-mounting hardware to be supplied by the customer • Note: Actuator extension harnesses not in kits, must be purchased separately (2 required) see page 42 15165-103 Electro-Polished Back Plate Dimensions 10" (25.4 cm) 12"(30.5 cm) 8" (20.3 cm) 5"(12.7 cm) 2" (5.1 cm) = Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below. Part # L" X W" Boat Length Min Transom Height 15164-103 19" x 14" 23' – 45' 10.5" (26.7 cm) 15165-103 24" x 14" 25' – 50' 10.5" (26.7 cm) Two Piece indicator switch included with kit SHIPPED FULLY ASSEMBLED
RkJQdWJsaXNoZXIy MjgzMDI=